- #COLT ADVANCED MEDIA CENTER REMOTE MAPPER INSTALL#
- #COLT ADVANCED MEDIA CENTER REMOTE MAPPER SERIES#
IP Phone to PSTN Phone, DTMF using RFC2833 SfB uses SILK for peer to peer if no bandwidth limitations are applied or detected, otherwise will use RTA for low bandwidth IP Phone A1 to PSTN 1, A1 conference to IP Phone A2, mixed codecs IP Phone A1 to PSTN 1, A1 conference to IP Phone A2, after answer IP Phone A1 to PSTN 1, A1 conference to PSTN 2, after answer PSTN 1 to IP Phone A1, A1 forwards to Mobile, No Answer PSTN 1 to IP Phone A1, A1 forwards to IP Phone A2, No Answer PSTN 1 to IP Phone A1, A1 forwards to PSTN 2, No Answer PSTN 1 to IP Phone A1, A1 forwards to Mobile, Unconditional PSTN 1 to IP Phone A1, A1 forwards to IP Phone A2, Unconditional PSTN 1 to IP Phone A1, A1 forwards to busy PSTN 2, Unconditional PSTN 1 to IP Phone A1, A1 forwards to PSTN 2, Unconditional PSTN 1 to IP Phone A1, A1 consultative transfers to PSTN 2 PSTN 1 to IP Phone A1, A1 blind transfers to PSTN 2 IP Phone to PSTN Phone, Mute both ends of call IP Phone to PSTN Phone, Long Duration Call IP Phone to International PSTN Phone, remote ringback PSTN Phone to IP Phone, network disconnect PSTN Phone to IP Phone, IP Phone disconnect after answer PSTN Phone to IP Phone, IP Phone no answer PSTN Phone to IP Phone, PSTN Phone disconnect after answer IP Phone to PSTN Phone, PSTN Phone disconnect after answer IP Phone to PSTN Phone, PSTN Phone no answer IP Phone to PSTN Phone, IP Phone disconnect after answer
Understanding the basic concepts of TCP/UDP, IP/Routing, and SIP/RTP are also necessary to complete the configuration and for troubleshooting, if necessary. There will be steps that require navigating third-party as well as the Ribbon SBC Command Line Interface (CLI). This is a technical document intended for telecommunications engineers with the purpose of configuring both the Ribbon SBC and the third-party product. The interoperability compliance testing focuses on verifying inbound and outbound calls flows between Ribbon SBC Edge and Skype for Business 2015.
#COLT ADVANCED MEDIA CENTER REMOTE MAPPER SERIES#
For additional information on Ribbon SBC Edge Series (Session Border Controller), please visit.For additional information on Skype for Business 2015, please visit.
This configuration guide supports features described on the Microsoft Technet web site. Just wanted to say that you helped me quite a bit with your post! Thanks.This document provides a configuration guide for Ribbon SBC Edge Series (Session Border Controller) when connecting to Skype for Business 2015 and Colt SIP Trunking. The available actions and general info about remote/keyboard mapping are described in the kodi wiki Keymap - Official Kodi Wiki kodi/temp/kodi.log while you press buttons to see which buttons are mapped to which keynames ("power", "red", "forward". I've been messing around with this all night and just annoyed that something I always use to setup in the past no longer works, even with the same tv.Įnable debug logging in kodi and watch the kodi log with tail -f. Exit keymap editor and all should work you would think but no blue button still opens photos. As I press it to map it it appears to have mapped successfully but makes the swoosh noise in the background like it's trying to open photos, so press back couple of times and save. By default blue button open photos, so I try and change it to context button like I have in the past.
#COLT ADVANCED MEDIA CENTER REMOTE MAPPER INSTALL#
That old tv is now in the conservatory so I've pulled out a spare sd card, fresh install of libreelec 8.2.5 and only installed keymap editor. Now here is how I know something has changed, when I use to use this same pi on my old living room tv last year i use to use keymap editor to change the coloured buttons to info/context menu etc and all worked perfect. It will not map through HDMI cec either using keymap editor. I've successfully done that and assigned a button to another key, now when I do this the button does nothing even though the ir-keytable sees that button as being setup up correctly. I've followed the wiki to configure my remote. Ok so I have come to the conclusion that something has changed in libreelec itself making the keymap editor useless now.
0 kommentar(er)
